n-Butyllithium manufacturers and suppliers

n-Butyllithium suppliers

Properties

Melting point:: -95 °C

Boiling point:: 80 °C

Density: 0.68 g/mL at 20 °C

Flash point:: 10 °F

storage temp.: 2-8°C

solubility: Miscible with diethyl ether and cyclohexane.

form: liquid

color: yellow

Specific Gravity: 0.695

Odor: Odor of the solvent

Water Solubility: vigorous reaction

Hydrolytic Sensitivity: 8: reacts rapidly with moisture, water, protic solvents

Sensitive: Air & Moisture Sensitive

BRN: 1209227

Exposure limits: ACGIH: TWA 50 ppm (Skin)
OSHA: TWA 500 ppm(1800 mg/m3)
NIOSH: IDLH 1100 ppm; TWA 50 ppm(180 mg/m3)

LogP: 1.25-2.31

Safety Information

Symbol(GHS): GHS02,GHS05,GHS07,GHS08,GHS09

Signal word: Danger

Hazard statements: H225-H250-H261-H304-H314-H336-H361f-H373-H411-H260-H361d-H410-H252-H318-H332-H401-H361

Precautionary statements: P210-P222-P231+P232-P261-P273-P422-P223-P370+P378-P280-P301+P310-P302+P334-P303+P361+P353-P304+P340+P310-P305+P351+P338-P331-P201-P301+P310a-P405-P422a-P501a-P262

Hazard Codes: F,C,N

Risk Statements: 14/15-17-34-48/20-51/53-62-65-67-63-35-11-15-50/53-66

Safety Statements: 6-9-16-26-36/37/39-45-61-62-6A-46-43B-43-60-33-29-5

RIDADR: UN 3399 4.3/PG 1

WGK Germany: 3

F: 3-10

TSCA: Yes

HazardClass: 4.3

PackingGroup: I

HS Code: 29319090

Toxicity: There is little toxicity data available for the butyllithiums; for data on ether and hydrocarbon solvents, see the appropriate LCSSs.

Use

N-Butyllithium must be calibrated through single titration as follows: 1) Titration solution: 1mol/L SEC butanol/dimethylbenzene solution (butanol and dimethylbenzene must be dried with an activated 5A molecular sieve) 2) Indicator: 2,2-dipyridine 3) Solvent: dimethylbenzene (must be dried with an activated 5A molecular sieve). 4) Operation method: Under the protection of argon, add magneton, 20ml dimethylbenzene and a small amount of indicator into a 100ml 3-lipped bottle with a tipping plug. Then use a precisely marked 2ml injector to swiftly transfer 2ml N-Butyllithium into the bottle (the air in the injector must be replaced with argon, which must then be expelled when collecting the N-Butyllithium; fill and drain the injector in the N-Butyllithium multiple times to prevent any water or air from remaining in the injector). The system should turn a purplish red. Then, wash, dry, and rinse the same injector with titration solution 2-3 times (to prevent any change in the amount added) and titrate the solution until the system turns yellow, and cease titration. 5) Repeat titration once; if the percent error between the two times is within 2%, the result can be regarded as correct. 6) Titration result: titration solution (ml)/2 to obtain N-Butyllithium concentration.

You can find n-Butyllithium suppliers, manufacturers, and distributors from countries such as China, United States and the India here. Browse to the tetrahydrofuran product information displayed by the supplier, as well as the supplier's contact and capability information.