Chemical Safety Data Sheet MSDS / SDS

Methyl methacrylate

Revision Date:2024-05-11Revision Number:1

SECTION 1: Identification of the substance/mixture and of the company/undertaking

Product identifier

  • Product name: Methyl methacrylate
  • CBnumber: CB8854425
  • CAS: 80-62-6
  • EINECS Number: 201-297-1
  • Synonyms: mma,Methyl methacrylate

Relevant identified uses of the substance or mixture and uses advised against

  • Relevant identified uses: For R&D use only. Not for medicinal, household or other use.
  • Uses advised against: none

Company Identification

  • Company: Chemicalbook
  • Address: Building 1, Huihuang International, Shangdi 10th Street, Haidian District, Beijing
  • Telephone: 400-158-6606

SECTION 2: Hazards identification

GHS Label elements, including precautionary statements

  • Symbol(GHS)
  • Signal wordDanger
Precautionary statements
P405 Store locked up.
P403+P235 Store in a well-ventilated place. Keep cool.
P370+P378 In case of fire: Use … for extinction.
P311 Call a POISON CENTER or doctor/physician.
P303+P361+P353 IF ON SKIN (or hair): Remove/Take off Immediately all contaminated clothing. Rinse SKIN with water/shower.
P301+P310 IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P260 Do not breathe dust/fume/gas/mist/vapours/spray.
P210 Keep away from heat/sparks/open flames/hot surfaces. — No smoking.
Hazard statements
H370 Causes damage to organs
H335 May cause respiratory irritation
H317 May cause an allergic skin reaction
H315 Causes skin irritation
H225 Highly Flammable liquid and vapour

SECTION 3: Composition/information on ingredients

Substance

  • Product name: Methyl methacrylate
  • Synonyms: mma,Methyl methacrylate
  • CAS: 80-62-6
  • EC number: 201-297-1
  • MF: C5H8O2
  • MW: 100.12

SECTION 4: First aid measures

Description of first aid measures

General advice
Show this material safety data sheet to the doctor in attendance.
If inhaled
After inhalation: fresh air.
In case of skin contact
In case of skin contact: Take off immediately all contaminated clothing. Rinse skin with water/ shower. Consult a physician.
In case of eye contact
After eye contact: rinse out with plenty of water. Remove contact lenses.
If swallowed
After swallowing: immediately make victim drink water (two glasses at most). Consult a physician.

Most important symptoms and effects, both acute and delayed

The most important known symptoms and effects are described in the labelling (see section 2.2) and/or in section 11

Indication of any immediate medical attention and special treatment needed

No data available

SECTION 5: Firefighting measures

Extinguishing media

Suitable extinguishing media
Carbon dioxide (CO2) Foam Dry powder
Unsuitable extinguishing media
For this substance/mixture no limitations of extinguishing agents are given.

Special hazards arising from the substance or mixture

Carbon oxides

Flash back possible over considerable distance., Container explosion may occur under fire conditions.

Combustible.

Pay attention to flashback.

Vapors are heavier than air and may spread along floors.

Development of hazardous combustion gases or vapours possible in the event of fire. Forms explosive mixtures with air at ambient temperatures.

Advice for firefighters

Stay in danger area only with self-contained breathing apparatus. Prevent skin contact by keeping a safe distance or by wearing suitable protective clothing.

Further information

Remove container from danger zone and cool with water. Prevent fire extinguishing water from contaminating surface water or the ground water system.

NFPA 704

2
3
2
HEALTH 2 Intense or continued but not chronic exposure could cause temporary incapacitation or possible residual injury (e.g. diethyl ether, ammonium phosphate, iodine)
FIRE 3 Liquids and solids (including finely divided suspended solids) that can be ignited under almost all ambient temperature conditions . Liquids having a flash point below 22.8 °C (73 °F) and having a boiling point at or above 37.8 °C (100 °F) or having a flash point between 22.8 and 37.8 °C (73 and 100 °F). (e.g. gasoline, acetone)
REACT 2 Undergoes violent chemical change at elevated temperatures and pressures, reacts violently with water, or may form explosive mixtures with water (e.g. white phosphorus, potassium, sodium)
SPEC. HAZ.

SECTION 6: Accidental release measures

Personal precautions, protective equipment and emergency procedures

Advice for non-emergency personnel: Do not breathe vapors, aerosols. Avoid substance contact. Ensure adequate ventilation. Keep away from heat and sources of ignition.

Evacuate the danger area, observe emergency procedures, consult an expert. For personal protection see section 8.

Environmental precautions

Do not let product enter drains. Risk of explosion.

Methods and materials for containment and cleaning up

Cover drains. Collect, bind, and pump off spills. Observe possible material restrictions (see sections 7 and 10). Take up with liquid-absorbent material (e.g. Chemizorb? ). Dispose of properly. Clean up affected area.

Reference to other sections

For disposal see section 13.

SECTION 7: Handling and storage

Precautions for safe handling

Advice on protection against fire and explosion

Keep away from open flames, hot surfaces and sources of ignition.Take precautionary measures against static discharge.

Hygiene measures

Immediately change contaminated clothing. Apply preventive skin protection. Wash hands and face after working with substance.

For precautions see section 2.2.

Conditions for safe storage, including any incompatibilities

Storage conditions

Keep container tightly closed in a dry and well-ventilated place. Keep away from heat and sources of ignition.

Storage stability

Recommended storage temperature 2 - 8 °C

Specific end use(s)

Apart from the uses mentioned in section 1.2 no other specific uses are stipulated

SECTION 8: Exposure controls/personal protection

control parameter

Hazard composition and occupational exposure limits
Does not contain substances with occupational exposure limits.

Exposure controls

Personal protective equipment
Eye/face protection

Use equipment for eye protection tested and approved under appropriate government standards such as NIOSH (US) or EN 166(EU). Safety glasses Tightly fitting safety goggles

Skin protection

Handle with gloves. Gloves must be inspected prior to use. Use proper glove removal technique (without touching glove's outer surface) to avoid skin contact with this product. Dispose of contaminated gloves after use in accordance with applicable laws and good laboratory practices. Wash and dry hands.

The selected protective gloves have to satisfy the specifications of Regulation (EU) 2016/425 and the standard EN 374 derived from it.

Splash contact Material: butyl-rubber

Minimum layer thickness: 0,3 mm Break through time: 66 min

Material tested:Butoject? (KCL 897 / Aldrich Z677647, Size M)

data source: KCL GmbH, D-36124 Eichenzell, phone +49 (0)6659 87300, e-mail sales@kcl.de, test method: EN374

If used in solution, or mixed with other substances, and under conditions which differ from EN 374, contact the supplier of the EC approved gloves. This recommendation is advisory only and must be evaluated by an industrial hygienist and safety officer familiar with the specific situation of anticipated use by our customers. It should not be construed as offering an approval for any specific use scenario.

Body Protection

Flame retardant antistatic protective clothing.

Respiratory protection

Recommended Filter type: Filter A (acc. to DIN 3181) for vapours of organic compounds

The entrepeneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are carried out according to the instructions of the producer.

These measures have to be properly documented.

Control of environmental exposure

Do not let product enter drains. Risk of explosion.

Exposure limits
NIOSH REL: TWA 100 ppm (410 mg/m3), IDLH 1,000 ppm; OSHA PEL: TWA 100 ppm; ACGIH TLV: TWA 100 ppm with intended TWA and STEL values of 50 and 100 ppm, respectively.

SECTION 9: Physical and chemical properties

Information on basic physicochemical properties

  • Appearancecolorless liquid
  • Odourpungent
  • Odour Threshold0.21ppm
  • pHNo data available
  • Melting point/freezing pointMelting point/range: -48 °C - lit.
  • Initial boiling point and boiling range 100 °C - lit.
  • Flash point10 °C - closed cup - DIN 51755 Part 1
  • Evaporation rateNo data available
  • Flammability (solid, gas)No data available
  • Upper/lower flammability or explosive limits Upper explosion limit: 12,5 %(V) Lower explosion limit: 2,1 %(V)
  • Vapour pressure 37 hPa at 20 °C - OECD Test Guideline 104
  • Vapour density ca.3,5 at 20 °C
  • Relative density0,94 at 20 °C
  • Water solubility15,3 g/l at 20 °C
  • Partition coefficient: n-octanol/waterlog Pow: 1,38 at 20 °C - OECD Test Guideline 107 - Bioaccumulation is not expected.
  • Autoignition temperature 435 °C at 1.013,25 hPa
  • Decomposition temperature No data available
  • ViscosityViscosity, kinematic: No data available Viscosity, dynamic: 0,53 mPa.s at 20 °C
  • Explosive propertiesNo data available
  • Oxidizing propertiesNo data available
  • Henry's Law Constant2.46 x 10-4 atm?m3/mol at 20 °C (approximate - calculated from water solubility and vapor pressure)

Other safety information

Surface tension 61 mN/m - OECD Test Guideline 115

Relative vapor density

ca.3,5 at 20 °C

SECTION 10: Stability and reactivity

Reactivity

Vapors may form explosive mixture with air.

Chemical stability

The product is chemically stable under standard ambient conditions (room temperature) .

Polymerizes with evolution of heat. Avoid contact with incompatible materials. Unless inhibited, product can polymerize, raising temperature and pressure, possibly rupturing container. Check inhibitor content often adding to bulk liquid if needed. Do not blanket or mix with oxygen-free gas as it renders inhibitor ineffective.

Possibility of hazardous reactions

Polymerizes readily unless inhibited.


Conditions to avoid

May polymerize on exposure to light.

Heat, flames and sparks. Heat. Extremes of temperature and direct sunlight. Warming.

Incompatible materials

rubber, various plastics, Strong oxidizing agents

Hazardous decomposition products

In the event of fire: see section 5

SECTION 11: Toxicological information

Information on toxicological effects

Acute toxicity
LD50 Oral - Rat - 7.872 mg/kg
Remarks: (RTECS)
LC50 Inhalation - Rat - male and female - 4 h - 29,8 mg/l Remarks: (ECHA)LC50 Inhalation - Rat - 4 h - 78.000 mg/m3
LD50 Dermal - Rabbit - male - > 5.000 mg/kg (OECD Test Guideline 402)
Skin corrosion/irritation
Skin - Rabbit
Result: Irritating to skin. - 4 h Remarks: (ECHA)
Serious eye damage/eye irritation
Eyes - Rabbit
Result: No eye irritation Remarks: (ECHA)
Respiratory or skin sensitization
(OECD Test Guideline 429)
Germ cell mutagenicity
Test Type: Ames test
Test system: S. typhimurium
Metabolic activation: with and without metabolic activation Method: OECD Test Guideline 471
Result: negative
Test Type: in vivo assay Species: Mouse
Application Route: Inhalation Method: OECD Test Guideline 478 Result: negative
Carcinogenicity
No data available
Reproductive toxicity
No data available
Specific target organ toxicity - single exposure
Inhalation - May cause respiratory irritation.
Specific target organ toxicity - repeated exposure
No data available
Aspiration hazard
No data available
Toxicity
The acute toxicity of methyl methacrylate is low. Irritation of the skin, eye, and nasal cavity has been observed in rodents and rabbits exposed to relatively high concentrations of methyl methacrylate. The chemical is a mild skin sensitizer in animals. The effect observed most frequently at lowest concentration after repeated inhalation exposure to methyl methacrylate is irritation of the nasal cavity. Effects on the kidney and liver at higher concentrations have also been reported.

SECTION 12: Ecological information

Toxicity

Toxicity to fish
flow-through test LC50 - Lepomis macrochirus (Bluegill sunfish) - 191 mg/l - 96 h

Remarks: (ECHA)


static test LC50 - Lepomis macrochirus (Bluegill sunfish) - 283 mg/l

- 96 h

Remarks: (ECHA)


Toxicity to daphnia and other aquatic invertebrates

flow-through test NOEC - Daphnia magna (Water flea) - 48 mg/l - 48 h

Remarks: (ECHA)


flow-through test EC50 - Daphnia magna (Water flea) - 69 mg/l - 48 h

Remarks: (ECHA)


Toxicity to algae
static test EC50 - Pseudokirchneriella subcapitata - > 110 mg/l - 72 h

(OECD Test Guideline 201)

static test NOEC - Pseudokirchneriella subcapitata - > 110 mg/l - 72 h

(OECD Test Guideline 201)

Persistence and degradability

Biodegradability aerobic - Exposure time 14 d

Result: 94 % - Readily biodegradable. (OECD Test Guideline 301C)

Biochemical Oxygen Demand (BOD)

140 mg/g

Bioaccumulative potential

No data available

Mobility in soil

No data available

Results of PBT and vPvB assessment

This substance/mixture contains no components considered to be either persistent, bioaccumulative and toxic (PBT), or very persistent and very bioaccumulative (vPvB) at levels of 0.1% or higher.

Other adverse effects

Additional ecological information

No data available

SECTION 13: Disposal considerations

Waste treatment methods

Incompatibilities

Vapor may form explosive mixture with air. Reacts in air to form a heat-sensitive explosive product @ 60℃. Incompatible with nitrates, oxidizers, peroxides, strong acids; strong alkalis; oxidizers, reducing agents; amines, moisture. Contact with benzoyl peroxide may cause ignition, fire and explosion.

Product

See www.retrologistik.com for processes regarding the return of chemicals and containers, or contact us there if you have further questions.

Waste Disposal

Consult with environmental regulatory agencies for guidance on acceptable disposal practices. Generators of waste containing this contaminant (≥100 kg/mo) must conform to EPA regulations governing storage, transportation, treatment, and waste disposal. Incineration may be allowed.

SECTION 14: Transport information

UN number

ADR/RID: 1247 IMDG: 1247 IATA: 1247

UN proper shipping name


ADR/RID: METHYL METHACRYLATE MONOMER, STABILIZED IMDG: METHYL METHACRYLATE MONOMER, STABILIZED


IATA: Methyl methacrylate monomer, stabilized

14.3

Transport hazard class(es)

ADR/RID: 3 IMDG: 3


IATA: 3

14.4

Packaging group

ADR/RID: II IMDG: II


IATA: II

Environmental hazards

ADR/RID: no IMDG Marine pollutant: no IATA: no

Special precautions for user

No data available

SECTION 15: Regulatory information

Safety, health and environmental regulations/legislation specific for the substance or mixture

Regulations on the Safety Management of Hazardous Chemicals
China Catalog of Hazardous chemicals 2015:Listed. website: https://www.mem.gov.cn/
Measures for Environmental Management of New Chemical Substances
Vietnam National Chemical Inventory:Listed. website: https://chemicaldata.gov.vn/
United States Toxic Substances Control Act (TSCA) Inventory:Listed. website: https://www.epa.gov/
Philippines Inventory of Chemicals and Chemical Substances (PICCS):Listed. website: https://emb.gov.ph/
New Zealand Inventory of Chemicals (NZIoC):Listed. website: https://www.epa.govt.nz/
Korea Existing Chemicals List (KECL):Listed. website: http://ncis.nier.go.kr
European Inventory of Existing Commercial Chemical Substances (EINECS):Listed. website: https://echa.europa.eu/
EC Inventory:Listed.
Chinese Chemical Inventory of Existing Chemical Substances (China IECSC):Listed. website: https://www.mee.gov.cn/

SECTION 16: Other information

Abbreviations and acronyms

  • ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
  • CAS: Chemical Abstracts Service
  • EC50: Effective Concentration 50%
  • IATA: International Air Transportation Association
  • IMDG: International Maritime Dangerous Goods
  • LC50: Lethal Concentration 50%
  • LD50: Lethal Dose 50%
  • RID: Regulation concerning the International Carriage of Dangerous Goods by Rail
  • STEL: Short term exposure limit
  • TWA: Time Weighted Average

References

【1】CAMEO Chemicals, website: http://cameochemicals.noaa.gov/search/simple

【2】ChemIDplus, website: http://chem.sis.nlm.nih.gov/chemidplus/chemidlite.jsp

【3】ECHA - European Chemicals Agency, website: https://echa.europa.eu/

【4】eChemPortal - The Global Portal to Information on Chemical Substances by OECD, website: http://www.echemportal.org/echemportal/index?pageID=0&request_locale=en

【5】ERG - Emergency Response Guidebook by U.S. Department of Transportation, website: http://www.phmsa.dot.gov/hazmat/library/erg

【6】Germany GESTIS-database on hazard substance, website: http://www.dguv.de/ifa/gestis/gestis-stoffdatenbank/index-2.jsp

【7】HSDB - Hazardous Substances Data Bank, website: https://toxnet.nlm.nih.gov/newtoxnet/hsdb.htm

【8】IARC - International Agency for Research on Cancer, website: http://www.iarc.fr/

【9】IPCS - The International Chemical Safety Cards (ICSC), website: http://www.ilo.org/dyn/icsc/showcard.home

【10】Sigma-Aldrich, website: https://www.sigmaaldrich.com/

Other Information

Usually contains hydroquinone, hydroquinone methyl ether and dimethyl t-butylphenol as inhibitors of polymerization.An added stabilizer or inhibitor can influence the toxicological properties of this substance, consult an expert.Do NOT take working clothes home.
Disclaimer:

The information in this MSDS is only applicable to the specified product, unless otherwise specified, it is not applicable to the mixture of this product and other substances. This MSDS only provides information on the safety of the product for those who have received the appropriate professional training for the user of the product. Users of this MSDS must make independent judgments on the applicability of this SDS. The authors of this MSDS will not be held responsible for any harm caused by the use of this MSDS.

Recommended Products
Tulipalin A SDS 2-Aminoethyl methacrylate hydrochloride SDS Coumarin-3-carboxylic acid SDS 2-Hydroxyethyl methacrylate SDS 3,4,5,6-Tetrahydrophthalic anhydride SDS CIS-ACONITIC ANHYDRIDE SDS Methanol SDS Methacrylic acid SDS Methacrylamide SDS Citraconic anhydride SDS